Uncategorized

Probe your cavity, save your time!


probing cavities to bulk-filling techniques styleitaliano style italiano

A clinical cases by our Community member Dr. Alessandro Colella.

 

Bulk-filling techniques have become more widely used thanks to the development of high-viscosity bulk composites. Improved curing, controlled polymerization contraction stresses and satisfying aesthetics allow dentists to perform satisfactory restorations in a short time. Working as a consultant often means to go fast. In this case two deep cavities were treated in a 16 y.o. young man at his first dental appointment, in only one hour, testing with my hands for the first time a new bulk composite (DMG Ecosite Bulk Fill; Shade Universal).



decayed teeth (II class 3.6 - 3.7) styleitaliano style italiano

Fig.1

This young patient came to my observation complaining about an increase in dental sensitivity in the third quadrant. Clinical and X-ray examination showed two decayed teeth (II class 3.6 – 3.7) and poor oral hygiene, especially on the lingual surface.



rubber dam isolation with also polydentia wedge styleitaliano style italiano

Fig.2

Rubber dam isolation was performed in order to have a dry and more comfortable working field and maximum tissue retraction. A plastic wedge (MyWedge – Polydentia) was put in place so as to protect the interproximal tissue and rubber dam.



deep caries styleitaliano style italiano

Fig.3

Despite the initial occlusal aspect, the caries had progressed really deep into the dentin.



cleaned cavities style italiano styleitaliano

Fig.4

Cavities were properly cleaned. Enamel edges were finished with fine-grained burs to prevent unsupported enamel prisms from chipping, thus causing micro-leakage. A slot was performed on the mesial wall of 37 in order to preserve the marginal ridge (2.5 mm thick) and not to lose anatomical information for further occlusal modeling. Because of the depth, a conventional II class should have been executed as well.



selective-etching strategy styleitaliano styleitaliano

Fig.5

Due to the considerable depth and the proximity to the pulp, a selective-etching strategy was preferred to reduce postoperative hypersensitivity.



appling universal adhesive on a dry cavity style italiano styleitaliano

Fig.6

A universal adhesive was applied on a dry cavity, in a self-etching mode, using a microbrush for 20 seconds. Excess was removed and the solvent evaporated by gently blowing air on the cavity.



light-curing style italiano styleitaliano

Fig.7

Light-curing for 40 seconds for each cavity.



Covering exposed dentin with a 0.5 mm flowable composite layer in order to protect the pulp styleitaliano style italiano

Fig.8

All the exposed dentin was covered with a 0.5 mm flowable composite layer in order to protect the pulp, increase the degree of conversion of the bonding agent, counteract the negative C factor of deep class I and II cavities, and reduce the cavity size for a subsequent faster filling.



probing cavities to bulk-filling techniques styleitaliano style italiano

Fig.9

The cavity size was measured with a probe, so that I could verify if a single bulk restoration was a viable option. Cavity depth measurement with a periodontal probe is a mandatory step in this case.



bulk-filling techniques with DMG bulk composite style italiano styleitaliano

Fig.10

High-viscosity bulk composite (DMG Ecosite Bulk Fill; Shade Universal) was chosen for a single shade restoration on both teeth.



filling cavities with polydentia ring and matrices, bulk-filling techniques styleitaliano style italiano

Fig.11

Slot cavity on 37 was filled first. Then a sectional matrix was placed (Lumicontrast, Polydentia) to build the distal wall of 36. Using black matrices is important to evaluate and achieve the right thickness of the interproximal wall. MyRing Classico easily ensures an optimal adaptation of the sectional matrix.



filling cavities bulk-filling techniques styleitaliano style italiano

Fig.12

The contact area seems to be adequate.



Essential Lines modeling technique, bulk-filling techniques styleitaliano style italiano

Fig.13

A single increment of composite for each tooth was enough to complete the fillings easily and quickly.



Essential Lines modeling technique, bulk-filling techniques style italiano styleitaliano

Fig.14

Some stains were used to give the restorations more volume.
It was an optional step to test this new material and its chromatic properties.



finishing and polishing bulk-filling techniques style italiano styleitaliano

Fig.15

Immediately after rubber dam removal and bite check, some occlusal adjustments were needed to remove some small premature contact on disto-lingual cusp.



bulk-filling techniques, essential lines style italiano styleitaliano



Fig.16

At one month check-up, the integration is satisfactory.



Conclusions



Using this strategy, the number of increments required to fill a cavity is reduced, compared with traditional incremental filling techniques. Instead of 2 mm increments recommended for conventional resin composites, we can apply up to 5 mm increments of the bulk-fill resin composites.
It means significant time saving that could be spent for finishing and polishing procedures, real key steps in long term longevity of a composite restoration.
Easy handling, also on the first use – like in this case that I performed – good aesthetic properties, in association with the right modeling technique can be the right recipe in the hands of anyone to achieve acceptable results in a very short time.



Bibliography



1) van Dijken JWV, Pallesen U. Bulk-filled posterior resin restorations based on stress-decreasing resin technology: a randomized, controlled 6-year evaluation. Eur J Oral Sci. 2017 Aug;125(4):303-309.
2) Fruits TJ, Knapp JA, Khajotia SS. Microleakage in the proximal walls of direct and indirect posterior resin slot restorations. Oper Dent. 2006 Nov-Dec;31(6):719-27.
3) Ilie N. Sufficiency of curing in high-viscosity bulk-fill resin composites with enhanced opacity. Clin Oral Investig. 2019 Feb;23(2):747-755.
4) Fronza BM, Abuna GF, Braga RR, Rueggeberg FA, Giannini M. Effect of Composite Polymerization Stress and Placement Technique on Dentin Micropermeability of Class I Restorations. J Adhes Dent. 2018;20(4):355-363.
5). Prager M, Pierce M, Atria PJ, Sampaio C, Caceres E, Wolff M, Giannini M, Hirata R. Assessment of cuspal deflection and volumetric shrinkage of different bulk fill composites using non-contact phase microscopy and micro-computed tomography. Dental Materials Journal, 37(3), 393-399.
6) Chiodera G. Essential Lines. Styleitaliano.org

The post Probe your cavity, save your time! appeared first on styleitaliano.org.


Source link

Leave your vote

0 points
Upvote Downvote
Show More

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button

Log In

Forgot password?

 

Don't have an account? Register

Forgot password?

Enter your account data and we will send you a link to reset your password.

Your password reset link appears to be invalid or expired.

Log in

Privacy Policy

Close